On my recent trip over to the river Yealm the winds were
fickle and so becalmed just off the western end of the breakwater, I had my first
opportunity to use Arwen’s new oars. 9’6” in length, built to plans from CLC, my
first rowing session didn’t go well.
Several issues emerged in rapid succession. The oars are a
little heavy and I haven’t quite positioned the oar leathers and collars correctly.
My seating position is definitely an issue. I perch on the aft end of the
centre case top, on a cushion to soften the pain of sitting over two deck eyes and
the cleat for the jib sheets. In this spot my feet touch the aft cockpit sole
but the oars are too high up my chest; change position and they are too low. Too
close to my chest. Too far away. Hands overlapping, hands too far apart.
So, some adjustments are needed and I turned to the hive
collective on my favourite five Facebook forums – Duckworks, Dinghy Cruising Association,
Wooden Boat forum, John Welsford Small Craft and Pocket Yachts and Trailer Sailors.
The first suggestions are obvious and sensible – remove the
seat cushion as it could be elevating my position badly; move the deck eyes and
jib cleat and sit on the top of the centre case and see if that makes a
difference.
Then we got into some technical stuff to consider.
The measurements of seating position, height of oarlocks
above the seat and position of the oarlock blocks are apparently critical. A
number of people commented that optimal distance from aft edge of seat to the
oarlocks should be 13 or 14”. Height of the oarlocks U bend should be around 6
- 8” above the seat level depending on the angle of the oar. Such positions
would allow room for looms to swing and dip. Some people suggested building a removable
thwart that could be added at seat top level just aft of centre board case.
This option wouldn’t necessitate me having to move the centre case jib sheet fittings.
I would, of course, have to think carefully about seat design – storage of it
etc.
Some people commented that my height might also be an issue
and that I should sit upright on the thwart, place the oars on the gunwales and
put my hands as far forward as they will go without leaning forward. The rowlocks
need to be at the point where the oars are aligned and at right angles to the boat.
Then, I’d need to adjust the height of the rowlocks so when the blades are in the
water the handles are at a convenient height.
And, most important apparently, I’d need to fit a footrest (or ‘stretcher’)
so that I can use my leg and back muscles effectively. Lack of a footrest loses most of my power. That
will take some thinking - a footrest that doesn’t interfere with the sleeping
platform boards which get stored on the sole between king plank and thwart side
wall.
There is another alternative – sculling instead of oars. There
was some discussion about the benefits of sculling but my concern is that
trying to find a sculling position off the transom might prove difficult. My
understanding is a scull would need to be near the centreline of the boat
transom. On my transom is a permanently mounted outboard bracket on the port
side, then the rudder head with tiller, the offset mizzen mast and finally the
boomkin. Its pretty crowded so unless I could design an offset sculling
position of some form….. However, one exceptionally experienced dinghy cruiser suggested that perhaps the oar could be kept in place by a rope loop around the oar and the mizzen mast. He felt there would be no need for a sculling notch since that would cause excessive friction with the oar.
And then there is the standing up – rowing forward option.
“Rowing while standing--if pushing on the oars--is quite
effective and comfortable, once the hang of it is gotten. I speak from river raft experience, only”
said one forum member.
Another, Rick suggested that extended rowlock crutches were
easy to make from bronze pipe and rod. The ID of pipe needs to be same as OD of
rowlock, then a rod needs to go in the other end with the OD equal to the ID of
the pipe and the ID of the rowlock socket. Depending on the geometry and
leverage I make, I might need to extend the rod into some kind of step but for
most light boats the socket should be plenty strong enough. Um!
Rick helpfully allowed
me to see photographs on his flickr account, some of which are found above and below.
Thanks Rick – the images have really helped – much appreciated.
A couple of people pointed out that in going for tall 12”
rowlocks, I should make sure I brace and support the base as there will be lots
of force generated and through-bolt the oarlock base to the block of wood I’ll use
for support.
Richard, of ‘Bootstrap’
navigator fame, has his tholes 12” above the gunnel and slightly overboard. He
says “Works well but very slow due to wide boat. Biggest issue is - where to
store the oars when not in use?”
So, some winter work to do - sorting out the rowing on Arwen. Last word though goes to Joel of navigator 'Ellie' fame. He carries a 6' paddle and an outboard - no oars - which made me sit up and think....do I really need oars?
