In the yahoo folders, I discovered a number of things which I may need to alter on Arwen. There is no doubt that my mast seems wrong. The sheave box is definitely in the wrong place and I will need to dig out the ans to check but it does seem around 10" lower than everyone else's. this would explain why trying to tighten the luff using the down haul is such a problem and why there seems to be a gap between the luff and the mast.
On the boomkin out back, I think I will replace the current eye arrangement with a metal screw in eye that can be repositioned to face the transom. It will mean the mizzen sheet leads right back to the transom without any turns in it. Less friction must be a good thing.
The down haul is attached to the top of the deck to one side of the mast......a roller arrangement and the halyard comes through a hole in the coaming or is tied to a cleat attached to the inside of the coaming. I actually think I prefer my down through the deck arrangement but I will take another look at it.
I think the top boom is too heavy and I need to taper it and shave some weight off it without losing the stiffness. Again I can take a look at the plans. The length is right and the width at one end is right but I didn't bother to taper it and I think doing so will help enormously.
I like the way some nav owners have drilled a series of circular holes insets of threes along the bottom edge of the internal coamings. Here they have tied on fenders, stored oars etc and actually it is a clever idea. So I will see what it might look like on Arwen. It would mean re varnishing the coaming but then it does need doing anyway.
I need to redo the reeling ties as well. A recent outing in which I had to double reef demonstrated that they were slightly too short...so lengthening them will make life easier afloat.
Someone has made two uprights that slot into the mast holes against which the mast and booms can be tied during transport.....a far better arrangement than the one I have now. Someone in Sweden had made lovely wooden slatted floor bases out of ash which looked stunning and practical.
I need to alter the lazy jacks. I need a triangular piece at the bottom of the sail either side so that more of the sail is caught between the two lazy jacks as it collapses down. In the meantime, some people have put a topping lift on the mizzen boom as well and I need to alter the lazy jack there so that it does both functions.
Some people have used halyard organisers to guide ropes back to the cockpit....wooden pieces with holes drilled I which are attached to the small sides running either isle of the centre case.
On the boomkin out back, I think I will replace the current eye arrangement with a metal screw in eye that can be repositioned to face the transom. It will mean the mizzen sheet leads right back to the transom without any turns in it. Less friction must be a good thing.
The down haul is attached to the top of the deck to one side of the mast......a roller arrangement and the halyard comes through a hole in the coaming or is tied to a cleat attached to the inside of the coaming. I actually think I prefer my down through the deck arrangement but I will take another look at it.
I think the top boom is too heavy and I need to taper it and shave some weight off it without losing the stiffness. Again I can take a look at the plans. The length is right and the width at one end is right but I didn't bother to taper it and I think doing so will help enormously.
I like the way some nav owners have drilled a series of circular holes insets of threes along the bottom edge of the internal coamings. Here they have tied on fenders, stored oars etc and actually it is a clever idea. So I will see what it might look like on Arwen. It would mean re varnishing the coaming but then it does need doing anyway.
I need to redo the reeling ties as well. A recent outing in which I had to double reef demonstrated that they were slightly too short...so lengthening them will make life easier afloat.
Someone has made two uprights that slot into the mast holes against which the mast and booms can be tied during transport.....a far better arrangement than the one I have now. Someone in Sweden had made lovely wooden slatted floor bases out of ash which looked stunning and practical.
I need to alter the lazy jacks. I need a triangular piece at the bottom of the sail either side so that more of the sail is caught between the two lazy jacks as it collapses down. In the meantime, some people have put a topping lift on the mizzen boom as well and I need to alter the lazy jack there so that it does both functions.
Some people have used halyard organisers to guide ropes back to the cockpit....wooden pieces with holes drilled I which are attached to the small sides running either isle of the centre case.
